{"product_id":"rms900103880","title":"Stator + Kokusan Flywheel + Puller Kit (RMS900-103880)","description":"\u003cp\u003e\u003cstrong\u003eRecall-Type Stator + Kokusan Flywheel Rotor + Gasket + Puller for Aprilia 2009–2020 RSV4 and 2011–2020 Tuono V4 – Replacement Part No. 2D000049 \/ 897479\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIntroducing the latest heavy-duty recall-type charging system upgrade kit for Aprilia 2009–2020 RSV4 and 2011–2020 Tuono V4 models.\u003c\/p\u003e\u003cp\u003eAnyone who rides or repairs Aprilia motorcycles is probably familiar with the stator, flywheel and voltage regulator issues common to these models. Many of these bikes experience at least one stator failure during their lifetime. The main issue was the use of extremely strong magnets in the original flywheels, which produced very high stator output and excessive heat. This often resulted in burned or shorted stator windings and, in many cases, a failed voltage regulator.\u003c\/p\u003e\u003cp\u003eThe solution was a new Kokusan flywheel with lower-strength magnets, reducing stator output and heat generation. This produces charging system output better matched to the bike's electrical requirements and helps improve the long-term reliability of the stator and voltage regulator.\u003c\/p\u003e\u003cp\u003eTo prevent or correct these flywheel problems, the engineers at RMS Labs developed a complete, heavy-duty charging system replacement kit for Aprilia. Upgrade your charging system today.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIncluded in this Kit:\u003c\/strong\u003e\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eHeavy-duty Kokusan recall-type OEM flywheel\u003c\/li\u003e\n\u003cli\u003eTriple-tested heavy-duty stator\u003c\/li\u003e\n\u003cli\u003eVoltage regulator rectifier\u003c\/li\u003e\n\u003cli\u003eCrankcase cover gasket\u003c\/li\u003e\n\u003cli\u003eFlywheel puller\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eThis kit allows you to upgrade the failure-prone charging system with a heavy-duty version using the latest technologies.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eFeatures:\u003c\/strong\u003e\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eKokusan upgrade\/recall-type flywheel:\u003c\/strong\u003e Lower-strength magnets provide correct stator output, reduced heat generation and improved long-term reliability.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBuilt to OEM size:\u003c\/strong\u003e Designed for a precise fit and straightforward installation.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eImproved epoxy:\u003c\/strong\u003e Uses high-temperature epoxy that is stronger than OEM epoxy, reducing the risk of magnet detachment.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHigh-grade steel capping:\u003c\/strong\u003e Helps prevent harsh additives in motor oil from degrading the epoxy securing the magnets. If a magnet comes loose, the sleeve is designed to prevent it from contacting the stator.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePrecise balancing:\u003c\/strong\u003e Helps eliminate crankshaft vibrations for improved engine longevity.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e\u003cstrong\u003eBefore Installing the New Stator:\u003c\/strong\u003e\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eCheck the AC output of the stator.\u003c\/li\u003e\n\u003cli\u003eReplace any burned or corroded connectors on the stator and regulator rectifier.\u003c\/li\u003e\n\u003cli\u003eCheck and repair any melted wiring.\u003c\/li\u003e\n\u003cli\u003eUse high-temperature dielectric grease on all connectors.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eThe stator may use a different wire colour code from the original. All wires are installed in the correct order; do not change any wiring configurations. This stator is designed as a direct plug-in replacement and should be used as such.\u003c\/p\u003e\u003cp\u003eWhen bolting the stator in place, always use locking compound. If the stator includes a pickup coil, ensure the air gap is correct during installation. We recommend setting it as close as possible, but no less than 0.010 inches.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore Installing the New Voltage Regulator Rectifier:\u003c\/strong\u003e\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eCheck the AC output of the stator.\u003c\/li\u003e\n\u003cli\u003eReplace any burned or corroded connectors on the stator and regulator rectifier.\u003c\/li\u003e\n\u003cli\u003eCheck and repair any melted wiring.\u003c\/li\u003e\n\u003cli\u003eUse high-temperature dielectric grease on all connectors.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e\u003cstrong\u003eFlywheel Installation:\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eBefore attempting to start the Aprilia, adjusting the air gap is necessary. Rotate the flywheel until the raised node is aligned with the pickup\/pulser coil. Adjust the gap as close as possible, but no less than 0.010 inches.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eFlywheel Puller:\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eRemoving a Powersport Vehicle's Flywheel \/ Rotor\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow It Works\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eFlywheel pullers are versatile engine service tools and are essential in every toolbox. A wide selection of rotor and flywheel pullers is available to fit many motorcycles and ATVs. They are simple to use, typically consisting of an outer body that holds the flywheel and a screw that pushes against the crankshaft. Some designs are even simpler, using only a bolt that threads into the flywheel. A taper holds the flywheel or rotor and crankshaft together, while the fixing bolt secures the flywheel to the shaft through applied torque.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eAn Important Component to Use\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eMany flywheel or rotor pullers include a small cap. This is a crankshaft thread protector and should always be used when supplied. Fit the cap onto the end of the inner piece of the puller, which presses against the tip of the crankshaft. This protects the fine threads from being stripped or damaged during flywheel or rotor removal.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eActions to Avoid\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eRemoving a flywheel or rotor is usually straightforward. However, corrosion, over-torquing the fixing bolt or repeated heat cycles can make removal difficult. Using a larger breaker bar or air impact tools to force the flywheel off can damage the flywheel, puller or crankshaft. Avoid these methods to prevent costly damage.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eTips for Releasing a Stuck Flywheel:\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eTorque Wrench\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eTo check whether the flywheel is stuck, set the torque wrench to 50 ft-lbs and try to ease the flywheel off. If it is not stuck, you should be able to remove it with less torque. If it is stuck, do not apply more torque, as this could break the wrench.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBall Peen Hammer\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIf 50 ft-lbs does not release the flywheel, use a 12 or 16 oz ball peen hammer. Strike the end of the flywheel puller with a medium blow. The impact may release the flywheel. Be prepared to catch it, as the shock can cause it to jump off. Always wear safety glasses.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003ePropane Torch\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIf the hammer does not work, heat may be used as a last resort. The heat should expand the flywheel without expanding the crankshaft as quickly, helping loosen the flywheel.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eImportant Safety Tips:\u003c\/strong\u003e To avoid setting fire to the garage, vehicle or yourself, take the following precautions before heating the flywheel:\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eClean any oil or flammable liquids from the flywheel.\u003c\/li\u003e\n\u003cli\u003eEnsure the work area is free of flammable liquids and is well ventilated.\u003c\/li\u003e\n\u003cli\u003eRemove the gas tank and place it at a safe distance.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eFocus the torch flame and heat only the centre of the flywheel. Some flywheels use adhesive or other compounds to secure the magnets in the rim, and concentrated heat can damage these materials. Be prepared to catch the flywheel if it comes off the crankshaft. Remember that it will be hot and take precautions to avoid burns.\u003c\/p\u003e\u003cp\u003eWith these tips and techniques, you can handle a stuck flywheel without damaging the puller or surrounding components.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWarning:\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eRisk of electric shock. Disconnect the battery before servicing.\u003cbr\u003eEnsure proper installation by a qualified technician to avoid malfunction.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eStator Dimensions:\u003c\/strong\u003e\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eInterior diameter: 43 mm\u003c\/li\u003e\n\u003cli\u003eExterior diameter: 105 mm\u003c\/li\u003e\n\u003cli\u003eThickness: 13.8 mm\u003c\/li\u003e\n\u003cli\u003eLength of wires from stator to grommet: 125 mm\u003c\/li\u003e\n\u003cli\u003eLength of wires from grommet to plug: 320 mm\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e\u003cstrong\u003eStator Specifications:\u003c\/strong\u003e\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eNumber of wires: 3\u003c\/li\u003e\n\u003cli\u003eNumber of plugs: 1\u003c\/li\u003e\n\u003cli\u003eNumber of pins: 3\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e\u003cstrong\u003eWire-to-Wire Resistance:\u003c\/strong\u003e\u003c\/p\u003e\u003cul\u003e\u003cli\u003eAlternator: Between each Yellow = 0.3 ohms ±20%\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003cstrong\u003eFlywheel Dimensions:\u003c\/strong\u003e\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eExterior diameter: 121 mm\u003c\/li\u003e\n\u003cli\u003eInterior diameter: 107 mm\u003c\/li\u003e\n\u003cli\u003eInterior diameter of centre housing: 19 mm\u003c\/li\u003e\n\u003cli\u003eExterior diameter of centre housing: 34 mm\u003c\/li\u003e\n\u003cli\u003eExterior thickness: 35.3 mm\u003c\/li\u003e\n\u003cli\u003eInterior thickness: 31.65 mm\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e\u003cstrong\u003eFlywheel Puller Specifications:\u003c\/strong\u003e\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eThread: 36 mm x 1.5 right-hand male\u003c\/li\u003e\n\u003cli\u003eLength: 60 mm\u003c\/li\u003e\n\u003cli\u003eExterior diameter: 48 mm\u003c\/li\u003e\n\u003cli\u003eInterior diameter: 35 mm\u003c\/li\u003e\n\u003cli\u003eExterior diameter of centre housing: 37 mm\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"RMSTATOR","offers":[{"title":"Default Title","offer_id":52123048837395,"sku":"RMS900103880","price":969.99,"currency_code":"NZD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0050\/7632\/0371\/files\/RMS900103880.jpg?v=1780125928","url":"https:\/\/www.motofusion.co.nz\/products\/rms900103880","provider":"MotoFusion New Zealand","version":"1.0","type":"link"}