STATOR & MOSFET REG KIT ASSTD TRI RFR FITMEN (RMS900-107634)
This product fits specific motorcycles and ATVs. Check the parts finder to confirm it fits your vehicle.
STATOR & MOSFET REG KIT ASSTD TRI RFR FITMEN (RMS900-107634) is backordered and will ship as soon as it is back in stock.
Hassle-Free Returns
Hassle-Free Returns
45-day change-of-mind returns on unused items in their original packaging. Read our returns and refund policy.
Closeout products are not eligible for change of mind returns. Read our returns policy in full.
Delivery & Shipping
Delivery & Shipping
This product is a dangerous good. Higher shipping rates may apply and delivery to some destinations will be delayed. See our shipping policy for details.
This is a bulky product. Additional shipping charges may apply and delivery to some destinations may be delayed or not possible. See our shipping policy for details.
Easy to understand, fast national shipping. Free shipping on non-bulky orders of $199 and over. See our shipping policy for full details.
STATOR & MOSFET REG KIT ASSTD TRI RFR FITMEN (RMS900-107634) is backordered and will ship as soon as it is back in stock.
Fitment
Fitment
Loading fitments...
Description
Description
Brand new aftermarket Generator Stator and RMSTATOR Red CNC-Machined Aluminium MOSFET Regulator kit.
- Direct replacement for the original unit.
- Plug-and-play, direct fit and easy installation.
- All products are tested before shipping.
Product images are accurate. If in doubt, compare the items with your original parts.
Generator Stator
- High-grade lamination materials.
- High-grade copper windings, resistant to temperatures up to 200°C.
- Pickup/pulsar coil included.
- Connectors included.
- Rubber grommet included.
RMSTATOR Red Machined Aluminium MOSFET Regulator
The red CNC-machined aluminium MOSFET voltage regulator is designed to improve heat dissipation in powersports charging systems. After 10 minutes of use, its billet aluminium heatsink runs up to 33% cooler than standard cast regulator housings. Equipped with MOSFET regulation technology, it is suitable for three-phase permanent-magnet charging systems.
- Runs cooler than OEM diode-style regulators.
- Overheat protection temporarily switches the regulator off to cool down instead of burning out.
- Direct replacement for the original unit.
- Plug-and-play, direct fit and easy installation.
- Quality exceeds OEM equipment.
- Improved heatsink and charging capabilities.
- Higher-grade electrical components.
- All products are tested before shipping.
The opposite connector (main harness side) is included. Original connectors can become melted, corroded or defective, causing recurring electrical issues.
Why use MOSFET technology?
- Runs cooler: Operates at lower temperatures than traditional shunt voltage regulator/rectifiers.
- Saves fuel: Reduces the load on the stator, requiring less engine work and fuel.
- Smoother charging: Provides steadier, smoother power to the battery.
- Extended battery life: Helps extend battery life and cold-cranking capacity.
- More engine power: Reduces stator load, allowing more engine power.
- Optimised performance: Advanced design lowers operating temperatures for improved longevity and performance. Power delivery is optimised by switching stator coils on or off.
Before installing the new stator:
- Check the AC output of the stator.
- Replace any burned or corroded connectors on the stator and regulator/rectifier.
- Check and repair any melted wiring.
- Apply high-temperature dielectric grease to all connectors.
The stator may have a different wire colour code from the original part. All wires are installed in the correct order; do not change the wiring configuration. This stator is designed as a direct plug-in replacement.
Always use thread-locking compound when securing the stator. If the stator includes a pickup coil, check the air gap during installation. Set it as close as possible, but no less than 0.010".
Before installing the new MOSFET voltage regulator/rectifier:
- Check the AC output of the stator.
- Replace any burned or corroded connectors on the stator and regulator/rectifier.
- Check and repair any melted wiring.
- Apply high-temperature dielectric grease to all connectors.
Warning:
Risk of electric shock. Disconnect the battery before servicing. Ensure proper installation by a qualified technician to avoid malfunction.
Generator Stator Dimensions:
- Interior diameter: 42 mm.
- Exterior diameter: 115 mm.
- Thickness: 18 mm.
- Stator-to-grommet wire length: 240 mm.
- Grommet-to-plug wire lengths: 190 mm and 880 mm.
- Pickup coil wire-to-grommet length: 270 mm.
Other Specifications:
- Number of wires: 5.
- Number of plugs: 2.
- Number of pins: 5.
- Number of poles: 18.
- Alternator resistance (black to black): 0.6 ohms ±20%.
- Alternator resistance to ground: O.L.
- Pickup coil resistance (green to black): 240 ohms ±20%.
RMSTATOR Red Machined Aluminium MOSFET Regulator Dimensions:
- Width: 95 mm.
- Length: 90 mm.
- Height: 30 mm.
- Wire lengths: 1,010 mm and 350 mm.
- Mounting holes, centre-to-centre: 75 mm.
Other Specifications:
- Number of plugs: 2.
- Number of pins: 5.
- Number of wires: 5.
- Minimum charging voltage: 14.5 V ±0.5 V.
- Maximum charging current: 50 A / 500 W.
- Open-circuit voltage: Less than 15 V.
- Operating temperature: -20°C to 85°C.
Specifications
Specifications
- Category (Primary)Hard Parts
- Category (Secondary)Electrical
- Category (Tertiary)Regulator / Rectifiers
- MPNRMS900-107634
Payment Methods
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.











