STATOR + CNC MOSFET KIT Honda CBR 600 RR 2013-2022
This product fits specific motorcycles and ATVs. Check the parts finder to confirm it fits your vehicle.
STATOR + CNC MOSFET KIT Honda CBR 600 RR 2013-2022 is backordered and will ship as soon as it is back in stock.
Hassle-Free Returns
Hassle-Free Returns
45-day change-of-mind returns on unused items in their original packaging. Read our returns and refund policy.
Closeout products are not eligible for change of mind returns. Read our returns policy in full.
Delivery & Shipping
Delivery & Shipping
This product is a dangerous good. Higher shipping rates may apply and delivery to some destinations will be delayed. See our shipping policy for details.
This is a bulky product. Additional shipping charges may apply and delivery to some destinations may be delayed or not possible. See our shipping policy for details.
Easy to understand, fast national shipping. Free shipping on non-bulky orders of $199 and over. See our shipping policy for full details.
STATOR + CNC MOSFET KIT Honda CBR 600 RR 2013-2022 is backordered and will ship as soon as it is back in stock.
Fitment
Fitment
Loading fitments...
Description
Description
Generator Stator + RMSTATOR Red Machined Aluminium MOSFET Regulator Kit
- Direct replacement for the original unit
- Plug-and-play, direct fit and easy installation
- All products are tested before shipping
Product images are accurate. If unsure, compare the items with your original parts before ordering.
Stator
- High-grade lamination materials
- High-grade copper windings resistant to temperatures up to 200°C
- Connectors included
- Rubber grommet included
RMSTATOR Red Machined Aluminium MOSFET Regulator
The red machined aluminium MOSFET voltage regulator is designed to improve heat dissipation in powersports charging systems. After 10 minutes of use, its billet aluminium heatsink runs 33% cooler than standard cast regulator housings. Equipped with MOSFET regulation technology, it is suitable for three-phase permanent magnet charging systems.
This regulator runs cooler than OEM diode-style regulators and includes overheat protection. If it gets too hot, it temporarily switches off to cool down rather than burning out.
- Quality exceeds OEM equipment.
- Improved heatsink and charging capabilities.
- Higher-grade electrical components.
An opposite connector (main harness side) is included, as original connectors are often melted, corroded or defective and can cause recurring electrical issues.
Why Use MOSFET Enhanced Technology?
- Runs cooler: Operates at lower temperatures than traditional shunt voltage regulator rectifiers.
- Saves fuel: Reduces the load on the stator, requiring less engine work and fuel.
- Regulated energy: Provides steadier, smoother battery charging.
- Extended battery life: Helps extend battery life and maintain cold-cranking capacity.
- More engine power: Reduces stator load, allowing more engine power.
- Optimised power delivery: Switches stator coils on or off to regulate power delivery.
- Enhanced design: Lowers operating temperatures for improved longevity and performance compared with the OEM part.
Before Installing the New Stator and Regulator
- Check the AC output of the stator.
- Replace any burned or corroded connectors on the stator and regulator rectifier.
- Check and repair any melted wiring.
- Apply high-temperature dielectric grease to all connectors.
The stator may use a different wire colour code from the original. All wires are installed in the correct order; do not change the wiring configuration. This stator is designed as a direct plug-in replacement. Always use thread-locking compound when securing the stator. If the stator includes a pickup coil, check the air gap during installation. Set it as close as possible, but no less than 0.010".
Warning
Risk of electric shock. Disconnect the battery before servicing. Ensure proper installation by a qualified technician to avoid malfunction.
Generator Stator Specifications
Dimensions:
- Interior diameter: 42 mm
- Exterior diameter: 115 mm
- Thickness: 12 mm
- Stator-to-grommet wire length: 100 mm
- Grommet-to-plug wire length: 365 mm
Other Specifications:
- Number of wires: 3
- Number of plugs: 1
- Number of pins: 3
- Number of poles: 15
- Alternator resistance (between each yellow wire): 0.4 ohms ±20%
RMSTATOR Red Machined Aluminium MOSFET Regulator Specifications
Dimensions:
- Width: 103 mm
- Length: 103 mm
- Height: 28 mm
- Mounting hole centre-to-centre distance: 80 mm
Other Specifications:
- Number of plugs: 2
- Number of pins: 5
- Number of wires: 0
- Minimum charging voltage: 14.5 V ±0.5 V
- Maximum charging current: 50 A / 500 W
- Open circuit voltage: 15 V
- Operating temperature: -20°C to 85°C
Specifications
Specifications
- Category (Primary)Hard Parts
- Category (Secondary)Electrical
- Category (Tertiary)Regulator / Rectifiers, Stators
- MPNRMS900-107597
Payment Methods
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.











